Apollo 1550ETL Manual de Instalação Página 1

1 Rev 1.0 INSTALLATION MANUAL Model 1550ETL–1K Single Swing Gate Operator Model 1650ETL-1K Dual Swing Gate Operator

10 1. Install all gate accessories such as Photo-Eye’s, Sensors, Loops and other safety devices. 2. Apply battery power to the 1050 gate operato

11 PUSH TO OPEN INSTALLATION Both measurements are taken from the center of the hinge. 11” 6” Direction of opening Gate (closed) Hinge post Top View

12 3 - CIRCUIT BOARD LAYOUT Figure 15 - CONTROL BOARD BUTTONS Figure 16 - CIRCUIT BOARD LAYOUT

13 Auxiliary Inputs 1 (16) and 2 (18): These digital inputs may be connected to the digital outputs of accessories and programmed to activate or cont

14 MOTB: Moon Touch programmable keypad with secure codes (up to 9 digits per code if required) to con-trol gate opening and closing. Connects to the

15 SMXI/A Plugin Receiver: The SMXI/A 433Plug-In Receiver provides up to 15 channels for specific control of individual gate functions. The receiver

16 OVIEW (see page 6 for Picture of OVIEW) Programming and diagnostic unit which connects directly to the gate controller and is part of the Nice “O

17 6.3 - Guard station 34 OPEN (NO) 35 STOP (NC) 36 CLOSE (NO) 37 GND With the Guard Station switches installed, the user can operate the gate by pu

18 Proper inspection of all equipment is required to ensure continuous functionality, safety and to ensure reliable op-eration in all weather conditi

19 Figure 25 - LAYOUT FOR IN-GROUND LOOPS Figure 26 - LAYOUT FOR PHOTOCELLS 8 - GENERAL LAYOUT AND SAFETY ACCESS

2 Table of contents IMPORTANT SAFETY INSTRUCTIONS …………………………………………………………...II APPLICATION ….……………………………………………………………………………………… III PRE-INSTALLATION

20 EXTERNAL ENTRAPMENT PROTECTION: Non-contact and contact sensors must be installed individually or in combination with each other to provide ex

21 Figure 27 - GENERAL BOARD OVERVIEW THE PROGRAMMING BUTTONS INDICATED IN THE ABOVE REFERENCE SHOULD BE USED ONLY AFTER UNDERSTANDING THE MANUAL AND

22 11 - PROGRAMMING BUTTONS Static: Set sensitivity to constant force on a scale of 1 to 10 (1 being the most sensitive). Dynamic: Set sensitivity o

23 11.5 - Function Learn: Puts the gate operator into learning mode for a Swing or Slide gate and Blue BUS peripherals. Learning mode for a Swing or

24 11.5 - Function (continued) Radio Channel: For the Plug-in Onboard Receiver, 15 radio channels may be programmed with one of the following option

25 11.5 - Function (Continued) Timer (continued) To program weekly events EV1 through EV8, perform the following steps: 1. Press FUNCTION -> Even

26 11.5 - Funcon (Connued) Advance Settings: The following settings are available for customizing the gate operator as required by the customer’s

27 11.6 - Display ESC: Exit the DISPLAY menu. Info: Displays the manufacturer name, product name/model, software versions, and serial number. Clock

28 CLASS IV - RESTRICTED ACCESS VEHICULAR GATE OPERATOR - A vehicular gate operator (or system) intended for use in a guarded industrial location or

29 TABLE 3 SYMPTOM(S) POSSIBLE SOLUTION Operator will not power On. Power LED is OFF  Check terminal Lock wiring for loose or broken wires  Chec

3 WARNING - To reduce the risk of injury or death:  READ AND FOLLOW ALL INSTRUCTIONS.  Installation should be performed by a professional instal

30 Learning 816-1K actuator 1. Connect battery power to board. 2. Install all gate accessories such as Photo-Eye’s, Sensors, Loops and other safety

31 Left box is for installer check off and the right box is for customer check off. 1. The gate has been checked to make sure it is level and moves

32 LIMITED TWO-YEAR WARRANTY Apollo Gate Operators are warranted against defects for a period of 24 months from the date of purchase

4 APPLICATIONS The Apollo Model 1550ETL-1K/1650ETL-1K Swing Gate Operator is approved for Vehicular Class I & II us-age under UL 325 Guidelines,

5 PRE-INSTALLATION CHECKLIST The following check list should be used before beginning installation: Verify that the proper operator has been selec

6 PART IDENTIFICATION OPTIONS Part# 11111B - CONTROL BOX Part# 816E Actuator with 8’ cable (816EX slave actuator with 38’ cable supplied with 1650 P

7 OPERATOR INSTALLATION Location of Pivot Point. 1/2 Center Line of attachment point for gate bracket Hinge post Vertical position of pivot arm Measu

8 Figure 5 - APOLLO 816-1K LIMIT SWITCH AND SMART SENSOR WIRING Apollo 816-1K operator green orange white yellow blue 1.4 - Apollo 816-1K limit switc

9 Figure 6 - APOLLO ACTUATOR MOTOR WIRING DIAGRAM Apollo 816-1K Red and Black Note - If gate moves in opposite di-rection from what is expected, r